INFLUENCE OF ROCK PHYSICAL AND MECHANICAL PROPERTIES ON THE ROCK RESISTANCE TO PNEUMATIC TRANSPORTATION BY THE PIPELINE SYSTEMS
- Деталі
- Батьківська категорія: Геотехнічна механіка, 2015
- Категорія: Збірник наукових праць "Геотехнічна механіка" Випуск-120
UDC622.648.6:621.867.8
Authors:
PonomarenkoS.N., Ph.D. (Tech), Senior Researcher
(IGTM NAS of Ukraine)
Abstract:
The paper studies influence of the rock physical and mechanical properties on the rock resistance to motion in the pneumatic pipeline systems.
The rock resistance to the motion in the pneumatic pipeline systems was studied by an integral coefficient of resistance in which resistance of the solid phase and air phase of the air mixture is summarized as the mixture was moving in the transporting pipeline. The dependences are formulated between integral coefficient of the resistance to motion and mode of transportation, parameters of transporting pipeline and air mixture which moves in this pipeline. Findings on dependence between a slip coefficient of different phases of the air mixture and resistance to motion of the rocks with different physical and mechanical properties are presented for each particular type of the transporting pipelines. Analysis of the obtained results has shown that rock bulk density has less significant influence on the rock resistance to be transported by the pneumatic pipeline than shape of the rock particles and rate of the rock aeration. The findings can be used for determining specific energy capacity of the pneumatic transporting pipeline systems for mining technologies.
Keywords:
integral coefficient of resistance, air mixture, rock, pneumatic transport, pipeline, slip ratio of the phases.
References:
1. Voloshin, A.I. and Ponomaryev, B.V. (2001), Mekhanikai pnevmotransportirowaniya sypuchikh materialov [Mechanics the pneumatic transport of bulk materials], Naukova dumka, Kiev, Ukraine.
2. Mills, D. (2003), Pneumatic conveying design guide, 2nd ed., Butterworth-Heinemann, Oxford, UK.
3. Mills, D., Jones, M.G. and Agarwal V.K. (2004), Handbook of Pneumatic Conveying Engineering, Dekker Mechanical Engineering, CRC Press, New York, USA.
4. Glebov, I.T (2009), Podyomno-transportnye mashiny otrasli. Lektsii i metody resheniya zadach po aspiratsii i pnevmotransportu derevoobrabatyvayushchikh predpriyatiy: uchebnoe posobie [Acting elevating-transportation machinery industry. Lectures and methods for solving problems of suction and pneumatic transport woodworking enterprises: Textbook], Ural State Forestry University, Yekaterinburg, Russia.
5. Gushchin, V.M. and Gushchin, O.V. (2010), "Analysis of driving modes in pneumatic conveying pipeline aeromixture", Visnyk Donbaskoyi derzhavnoy mashinobudivnoi akademiyi, no.1(18), pp. 78–83.
6. Chaltsev, M. and Bugaev, B. (2010), "Analytical and Experimental Studies of the Critical Regimes of the Bulk Solids Pneumatic Conveying", Visti Avtomobilno-dorozhnogo institutu: naukovo-vyrobnychyi zbirnyk, no.1(10), pp. 5–11.
7. Chaltsev, M. (2005),"Hydraulic Calculation Closer Definition of the Aerodisperse Flows of Dusting Materials", Visti Avtomobilno-dorozhnogo institutu: naukovo-vyrobnychy zbirnyk, no.1, pp. 11–16.
8. Levy, A. (2000), "Two-fluid approach for plug flow simulations in horizontal pneumatic conveying", Powder technology, vol. 112, no 3, pp. 263 – 272.
9. Jones, M. G. and Willms, K. C. (2003), "Solids friction factors for fluidized dense-phase conveying", Particulate Science and Technology: An International Journal, vol. 21, no 1, pp. 45 – 56.
10. Datta, B. K. and Ratnayaka, C. (2003), "A simple technique for scaling up pneumatic conveying systems", Particulate Science and Technology: An International Journal, vol. 21, no. 3, pp. 227 – 236.
11. Ratnayake, C., Datta, B.K. and Melaaen M.C. (2007), "A unified scaling-up technique for pneumatic conveying systems", Particulate Science and Technology: An International Journal, vol. 25, no. 3, pp. 289 – 302.
12. Poturayev, V.N., Bulat, A.F., Voloshin, A.I., Ponomarenko, S.N. and Voloshin, A.A. (2001), Mekhanika vibratsionno-pnevmaticheskikh mashin ezhektornogo tipa [Mechanics vibration-pneumatic machine the ejector type], Naukova dumka, Kiev, Ukraine.
13. Ponomarenko, S.N. (2013), "Influence of aero mixture characteristics on technological parameters of pneumatic transportation stowing settings the ejector type", Geo-Technical Mechanics, no.109, pp. 63–73.
14. Ponomarenko, S.N. (2012), "Influence of size of particles of mountain breed on parameters of pneumatic portage", Geo-Tecnical Mechanics, no.97, pp. 264–271.
15. Shashenko, A.N., Maykherchik, T. and Sdvizhkova, E.A. (2005), Geomekhanicheskie protsessy v porodnykh massivakh [Geomechanical processes in rock masses], National Mining University, Dnipropetrovsk, Ukraine.
About the author:
Ponomarenko Sergei Nikolaevich, Candidate of Technical Sciences (Ph.D), Senior Researcher, Senior Researcher of department of vibropnevmoatic Transport Systems and Complexes, M.S. Polyakov Institute of Geotechnical Mechanics under the National Academy of Science of Ukraine (IGTM, NASU), Dnepropetrovsk, Ukraine, Ця електронна адреса захищена від спам-ботів. вам потрібно увімкнути JavaScript, щоб побачити її.